LAKE LM44

LAKE Ref : LM44


90,00 € HT

processeur 4 IN / 4 OUT + AES + DANTE


 

Features
Module configuration 2 Contour or 4 Mesa modules
Channel processing 6 in Contour mode, 4 in Mesa mode
Input routers 8 input routers with 4 priorities in each, seamless failover to lower priorities
Module input mixer 4 ch. for Contour, 8 ch. for Mesa-modules. Mix any ratio between all input routers.
Input processing Parameteric EQ with Mesa and Ideal Graphic equalizers, both utilizing Raised Cosine algorithms
Output processing Linear phase or Classic crossovers, Parametric EQ, shelving and all-pass filters
Features Delay, Mute, Phase, Gain etc.
Limiters LimiterMax with Peak and RMS limiter. Confi gurable MaxRMSLevel, MaxRMSCorner, MaxRMSAttack, MaxRMSRelease and MaxPeakLevel
SuperModule compatible Yes
Audio Performance
Conversion resolution 24-bit
Internal Sample Rate / Data path 96 kHz / 32 bit floating point
Product propagation delay Best case (AES synchronous 96 kHz to AES synchronous 96 kHz via module) 0.871 ms Analog (Analog in to Analog out via module) 1.049 ms Pass thru (Analog in to AES synchronous 96 kHz bypassing module) 0.158 ms
Maximum available user delay 2 seconds
Analog
Inputs and Outputs 4 inputs, 4 outputs
Frequency response, analog-to-digital +/-0.1 dB, 20 Hz to 20 kHz
Frequency response, digital-to-analog +/-0.03 dB, 20 Hz to 20 kHz
THD+Noise, inputs 0.00024% typical at 1 kHz
THD+Noise, Outputs 0.00037% typical at 1 kHz
Dynamic range, inputs 116 dB
Dynamic range, Outputs 115 dB
Input impedance 20 kOhm balanced, 10 kOhm unbalanced
Output impedance 50 ohms
Maximum input level +26 dBu
Input sensitivity - settings for digital full-scale +12 dBu, +26 dBu
Maximum output level 21 dBu
Crosstalk, inputs -98 dB, 20 Hz to 20 kHz
Crosstalk, outputs -98 dB, 20 Hz to 20 kHz
Common mode rejection ratio (CMRR) >70 dB, 20 Hz to 20 kHz
Dante Audio Network
Inputs and Outputs 4 inputs, 8 outputs
Supported sample rates 48, 96 kHz
Support redundant paths Glitch-free Dual Redundant Dante using two Ethernet networks
Receiver latency 0.5 ms, 0.8 ms, 1.3 ms, 4 ms
Device presets
Frame presets 100
AES3/EBU (sample rate converters available as desired)
Inputs and Outputs 8 inputs, 8 outputs
Supported sample rates 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz, 192 kHz (I/O individually selectable)
Supported resolutions Up to 24-bit
THD + Noise 0.00002 % at 96 kHz and 0.00006 % at 44.1 kHz sample rate
Dynamic range Base48 -140 dBFS, Base44 -125 dBFS
Clocking
Clock selection Manual or automatic according to priority scheme
Oscillator type / synchronization High quality VCXO clock can provide Dante master clock or slave. Automatic synchronization with Dante network.
Base48 2 (Primary and SRC)
Base44 1 (SRC)
Clock accuracy < ± 7 ppm
GPIO
Inputs 2 General Purpose Inputs (GPI) supporting external contact closure
Outputs 2 General Purpose Outputs (GPO) with internal contact closure
Software configurable input control Standby state, Mute state, Dual preset recall
Software configurable output indication Standby state, Mute state, Faults, Ready
Back panel Interface
Analog Inputs and Outputs 4 + 4 XLR
AES Inputs and Outputs DB-25, with selectable termination
Ethernet Ports Auto 100/1000, Auto uplink, 2 x Neutrik etherCON RJ45 connectors
GPIO DB-9
Power Detachable locking 3-pin IEC
Control and monitoring interface Via Ethernet for Lake Controller software, or DLM (the 3rd party protocol)
Front-panel user interface
Display Daylight readable monochrome (128 x 64)
Meters LED for signal level and clip indicators per channel
Mute access Dedicated Mute button and LED indication per processing channel
Menu Intuitive and powerful user interface with soft keys
System status indication LED Fault and Warning indication and detailed description on display
Parameter adjustment Single/multiple parameter edits with rotary encoder
Power
Nominal voltage 100 – 240 VAC
Operating voltage 70-265 V AC
Power consumption 30 W maximum
Dimensions
Dimensions 483 mm (19"), 44 mm (1 U), 290 mm (11.5")
Weight
Weight 5 kg (11 lbs)